All right, today we’re gon na, be taking. A look at the tulsa arcades monitor upgrade kit, we’ve got a 20 inch bezel here with, the graphic installed went. With just a basic plain big buck hunter. Black bezel art and then just the basic art here on the bottom. They’ve got different options: different farmhouse, graphics, you can get. You know the big buck hunter logo up here at the top, but i just wanted something plain and simple: underneath it we have. The plexiglass overlay, it is covered up with the protective layer, so that’s why it looks like cardboard and of course we have the monitor mounting bracket. So you can do this yourself if you want to cut out a board, but you know for people that are not wood handy so to speak. Tulsa arcades makes these very handy, monitor mounts, so you can get it out there. You can install it on the back of monitor and you can actually adjust it by sliding up and down. We got my dell 20 inch monitor here. As you can see, you just throw the monitor bracket there on the back comes with all the supplied hardware that you,’ll need, and you’ll simply just take these l brackets secure those into these sides and you’ll go ahead and install this Into the kit, so now that i’ve got the monitor bezel installed there. One thing to note is this: bezel is made a little bit longer, so it’s actually meant to slide in the grooves there. As far as making sure you line everything up correctly, the easiest way to do it is number one. Have your control panel, adjusted and kind of in there you don’t have to necessarily install it put the screws in there, but you want it nice and secure where it would normally rest, then that’s how you’re going to line up your Monitor so i’m going to make sure i slide in the edges here into the supplied grooves and then i’ll go ahead and secure the side brackets to the side panels of the machine all right. So now that we have the monitor mounted, we need to do something about the pcb, so i went ahead and took it out of its stock. Little housing won.’t be able to really reuse this, because this was meant to mount on the back of the stock monitor. So i went ahead and took it out of that casing. Here we have the raw pcb itself went ahead and put some double sided tape on the back side of it. That way, i can basically put this anywhere in the cabinet. I so desire hooking it up very simple. You know you’re just going to connect your normal standard connections. This end’s going to go to the control deck, but we’re going to be using the geekworm lvds to hdmi. Adapter converter got my red dot all the way. To the right hand, side on the converter board, you can use actually the top or the bottom. I’m, going to make sure my red dot is lined up with this section right here on the board, plug it in good. Now this is going to allow us to connect an hdmi input, slash output, so we’ll take an hdmi connection. There we go and that will take the video signal out of the big buck hunter pcb drive it to hdmi input to our monitor. However, our monitor, specifically the dell monitor that we’re using, does not have hdmi inputs. What i’m going to use is one of these dvi to hdmi adapters. I’m going to plug, in the other end of my hdmi. There plug this into the back of the dell monitor and we’ll be good to go. All right pcb is mounted geek worm board is mounted over here to the side. Like i said, you can really mount it wherever you want, i’ve just thrown it there. For now you need to do some. Cable management got to be cognizant of the fact that the guns are going to be inside the cabinet. So you don’t want cables dangling down here, and you know interfering or inadvertently getting unplugged. We’ll have to use a secondary power supply just because, since we are needing to power up the dell monitor, we’re no longer able to just run everything straight from the stock. You know arcade 1up power supply and there we have it no problem at all fit like a glove, nice and clean sleek lines, no issues whatsoever with the install and the 20 inches. I mean it just makes this game so much more enjoyable. Obviously, you can go bigger if you want, you can throw on like a 32 inch tv. I just wanted the biggest i could put while maintaining the cabinet. You know form and function. I didn’t want things sticking out to the sides, because this is going to be a gift for my father and i know he:’s got limited space, so i didn’t want some giant flat screen. You know sticking off the front of this. So i know he’s going to have limited space for this. But overall i got to say i’m very happy with the the bezel, the mount kit and everything from tulsa arcades again, if you’re a good handy, woodworking type of guy, you can do all this yourself. You can get plexiglass from lowe,’s and home depot, and things like that. But if you just want something very convenient, very easy, all you have to do is you know, put a couple screws in this is probably the best option for you just because it takes a lot of the guesswork out of things like that and you can get It done in, like 15 minutes tops, but now it’s time for me to shoot some bucks. So if you enjoy the content, make sure you hit that like button share this video with your friends, if you found the information helpful and as always thanks for watching guys, it really means a lot. You
